Search the Community

FYI @DevonianDigger @JamesAndTheFossilPeach @Kane @Malcolmt @caldigger @RJB @Ptychodus04 @Fossildude19 @FossilSloth @FossilDudeCO I need your guy's input as I go along! I'm a green horn! Thank you in advance. Well since some of you who I know have started your own fossil preparation threads I thought I'd do the same. A lot has transpired since, well Saturday morning. I went all chips in and bought a really nice two stage, 60 gallon Kobalt air compressor. You don't want to know the cost. My jaw dropped when the cashier rang up the total but I had no other choice. I was all in at this point. Went home and my neighbors helped me lift this monster out of my cousins pickup and I spent the rest of the day setting everything up then realized that I didn't have the connector for the 3/4 output on the tank so went back today and figured it out. The Lowes guy and I had fun figuring this puzzle out together. So I have a moisture trap, emergency shutoff (isolator) valve, regulator, 25 foot air hose, CP-9361, some fossils to prepare, and 240 volt connection (yes I wired up the plug and cabling). Wiring up this 240 volt electrical housing was probably the scariest thing I've ever done in my life. Definitely not a lot of room for error. Really was nervous about doing this. Also nervous about this. Had to punch a hole through 11 inch dry wall and plywood to get to the washer/dryer room to access the 240 volt dryer outlet. Thankfully we weren't using that outlet as our drier runs on natural gas. Here's the big 250 lb air compressor. This thing pumps out a ton of air. I was able to run the scribe continuously for three hours. No stopping! Moisture trap, shut off valve, and the regulator all hooked up to a large 3/4 elbow. One of the reasons why I had to get the elbow was because I knew with all the extra valves and connections it would put strain on the line so I wanted gravity to compliment the setup (as punishing as gravity can be at times). So now for the good part. The fossils. Recently acquired a massive Tumidocarcinus giganteus crab concretion from New Zealand. Within a few hours the carapace is well exposed. I'm not exactly sure what to look for here. There's either an exoskeleton that's flaking off or that's some sort of chemical process on the outside. I'm really not sure as I've seen these crabs in both that light pinkish hue and then in the black color. Where the black is was where the concretion was exposed to the elements. You can see the non-dominant left claw being teased out. That's also delicate so I've really been taking my time. Worked on it for about 3 hours total. So far so good. Here's a couple pictures to illustrate the process. Unlike @RJB I may not have a beer by my side but I'm ready to go crabbing. Definitely needed the safety goggles. Will need to pickup an air mask tomorrow along with some noise cancelling headphones (have some Beats at work). Roughly 10 minutes in and am really taking my time (don't want to do anything that I might regret later). About 40 minutes in. Slowly inching my way towards the left claw. About two hours into the process. The carapace is starting to show. Decided to leave at this point with nearly three hours invested. I hear crabs can have leg parts in virtually any arrangement depending on their displacement and preservation but I'm anticipating legs going from the carapace region out towards the edges (you can see points where legs should be). Really decided to slow down and take my time. I think this is going to be a very special fossil especially since it's the first crab I'm preparing and the first fossil prepared by my first owned air scribe the tried and true CP-9361. I'm sure I'll make mistakes along the way and I'm not doing this the way other more experienced prepares would but it's a start. The CP-9361. I'm in love. Then for kicks I decided to do some work on this little Knightia from the split fish layers. The Museum of Ancient Life curator that I've been volunteering with has been teaching me the ways of prep. Some secrets I won't be able to divulge here as I've sworn an oath of secrecy but he's really good at preparing Green River fish. He actually uses a CP-9361 so I figured why couldn't I right? Well I went in really slowly on this fish and exposed it in about five minutes flat. There's a few punch holes on the far end of the tail from where I was a tad bit to aggressive with the scribe but with time and practice I'll get a better feel for how to work with this soft matrix. I'm sure the 18 inch layer is a bit harder. Still I think it came out for a common fish and it looks pretty good. I forgot to take a before picture but here's an after picture. Little Knightia required only 5 minutes of preparation work with the CP9361 when it would have taken at least an hour with dental picks, which I'm never going back to again.