Ludwigia Posted July 21, 2020 Share Posted July 21, 2020 I recieved a large (32cm. in diameter) ammonite on commission recently which turned out to be rather complicated to prepare. It's a Fissilobiceras sp. from the ovale zone in the Early Bajocian from the Wutach valley. Most of it was imbedded in matrix, so it wasn't possible to judge at first in what kind of condition the inner whorls were and it was too fragile to just have a quick go at it with hammer and chisel in order to find out, so I had to take the slower route peeling off layer after layer with the stylus. Here's how both sides looked to begin with. After a good number of hours work with the stylus it became obvious for one thing, that the whorls were beginning to dip deeply down radically on their way to the center and there was less and less separation layer to the steinkern available until it practically completely disappeared, so I figured I'd have to stop at this point with the pen work. I also inadvertently dug out a bit too much due to the deformation. On the positive side, however, the inner whorls turned out to be intact. So I changed over to the abrader to remove the remaining thin matrix layer to get a proper view of the lay of things and to help decide how to continue. The circles and arrows on the last 2 photos were used during the exchange between the owner and myself in order to decide how I should proceed with the work, since these ammonites are not easy to find, particularly at this size, and so we decided in the end to make a matrix display out of it. I then removed the rest of the matrix from above the living chamber until its end and abraded that as well. The last step was to fill the gaps with Apoxie modelling compound and to round things off a bit. Once that was hardened, I balanced the colors with waterpaint and then applied a coat of Rember beeswax finish and the job was done. One interesting thing about this piece is that the border between phragmocone and somewhat flattened living chamber is easy to differentiate. The living chamber would certainly have been larger, but that was all I was able to save, and the whorls at the bottom were practically nonexistent, so I figure I got the best out of this one that I could. 11 Greetings from the Lake of Constance. Roger http://www.steinkern.de/ Link to comment Share on other sites More sharing options...
ntrusc Posted July 21, 2020 Share Posted July 21, 2020 Turned out great, nice work Regards Neil. Link to comment Share on other sites More sharing options...
Ludwigia Posted July 21, 2020 Author Share Posted July 21, 2020 9 minutes ago, ntrusc said: Turned out great, nice work Regards Neil. Thanks 1 Greetings from the Lake of Constance. Roger http://www.steinkern.de/ Link to comment Share on other sites More sharing options...
Fossildude19 Posted July 21, 2020 Share Posted July 21, 2020 Amazing work, Roger! Tim - VETERAN SHALE SPLITTER VFOTM --- APRIL - 2015 __________________________________________________ "In every walk with nature one receives far more than he seeks." John Muir ~ ~ ~ ~ ><))))( *> About Me Link to comment Share on other sites More sharing options...
Wrangellian Posted July 21, 2020 Share Posted July 21, 2020 As always, quite the transformation between start and finish. I'll bet the owner is proud to have that one in their collection. Link to comment Share on other sites More sharing options...
Ludwigia Posted July 22, 2020 Author Share Posted July 22, 2020 3 hours ago, Fossildude19 said: Amazing work, Roger! Thanks Tim. 49 minutes ago, Wrangellian said: As always, quite the transformation between start and finish. I'll bet the owner is proud to have that one in their collection. He wasn't figuring that it would end up in the display case, but now it will Greetings from the Lake of Constance. Roger http://www.steinkern.de/ Link to comment Share on other sites More sharing options...
Wrangellian Posted July 22, 2020 Share Posted July 22, 2020 36 minutes ago, Ludwigia said: He wasn't figuring that it would end up in the display case, but now it will I probably would do the same, the sutures are showy. Link to comment Share on other sites More sharing options...
FossilNerd Posted July 27, 2020 Share Posted July 27, 2020 Great job Roger! You are the ammonite master! The good thing about science is that it's true whether or not you believe in it. -Neil deGrasse Tyson Everyone you will ever meet knows something you don't. -Bill Nye (The Science Guy) Link to comment Share on other sites More sharing options...
Ludwigia Posted July 27, 2020 Author Share Posted July 27, 2020 7 hours ago, FossilNerd said: Great job Roger! You are the ammonite master! Thanks Greetings from the Lake of Constance. Roger http://www.steinkern.de/ Link to comment Share on other sites More sharing options...
RJB Posted August 7, 2020 Share Posted August 7, 2020 I would say you did a fantastic job on an ammonite that was a bugger to prep!!! RB Link to comment Share on other sites More sharing options...
Bobby Rico Posted August 7, 2020 Share Posted August 7, 2020 Can’t be prepped any better. Great work mate. Link to comment Share on other sites More sharing options...
Ludwigia Posted August 7, 2020 Author Share Posted August 7, 2020 2 hours ago, RJB said: I would say you did a fantastic job on an ammonite that was a bugger to prep!!! RB 2 hours ago, Bobby Rico said: Can’t be prepped any better. Great work mate. Thanks guys Greetings from the Lake of Constance. Roger http://www.steinkern.de/ Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now