Jump to content
Ptychodus04

Vaniman Abrasive Blaster Review

Recommended Posts

Ptychodus04

Today I received my @Vaniman Mobile Problast. I ordered it Monday and it shipped the same day. I had a few questions and Nathan was prompt and answered all my questions.

 

It arrived on my doorstep double boxed and well packed. Upon unpacking, the unit was inspected and found to be in order.

A49498B3-09AE-4E12-8B0E-03246075D22D.thumb.jpeg.c819229b215fad52ba781685bfcd9ca8.jpeg

 

The unit came with supplied with a 1/4” barbed hose fitting. For the air inlet.

57A12100-CF6F-458F-9BB5-85B77C183AE2.thumb.jpeg.62c4fdd6a9591be95af2093b3be79fd9.jpeg

 

In the package also came a 1/4” quick connector. Which was easily changed out.

 

6C3E68B5-4421-4A06-B7AE-BD4AADBA2172.thumb.jpeg.5deb820396837ac8190c63f4adafd278.jpeg

 

I connected it to the 1/4” tubing I picked up at the hardware store and connected that to my compressed air line downstream from my filtration and desiccant system, filled the hopper with baking soda, and fed the nozzle into the blast cabinet.

 

Share this post


Link to post
Share on other sites
goatinformationist

Your new toy beats my hammer, pick, and dremel by a mile.  Hats off to you.:tff:

Share this post


Link to post
Share on other sites
Tidgy's Dad

Very nice indeed! :)

I look forward to your next set of experiments. 

Share this post


Link to post
Share on other sites
rebu

Very nice, congrats. Did you get the set complete with the pen and all the hoses or do you have to get it separately? Man I will love to have a toy like that :dinothumb:

Share this post


Link to post
Share on other sites
RJB

This unit sounds real good.  Only have two questions.    You mention filtration.  What are you filtering?   and may I ask what size tip/nozzle you are using?   Thanks

 

RB

Share this post


Link to post
Share on other sites
Ptychodus04
7 hours ago, rebu said:

Very nice, congrats. Did you get the set complete with the pen and all the hoses or do you have to get it separately? Man I will love to have a toy like that :dinothumb:

It all came as one unit, fully assembled. I only had to supply the 1/4” inlet hose and a connector to attach to my compressed air line.

6 minutes ago, RJB said:

This unit sounds real good.  Only have two questions.    You mention filtration.  What are you filtering?   and may I ask what size tip/nozzle you are using?   Thanks

 

RB

I have 2 oil/water separators and a desiccant canister filtering the compressed air. The tip is  .048” (1.2mm) sapphire imbedded. I also ordered a .036” (.91mm) tungsten carbide tip for more detailed work.

Share this post


Link to post
Share on other sites
Kane

What is the max safety PSI on this one, Kris?

Share this post


Link to post
Share on other sites
TyBoy

This looks great thanks for sharing.  Might get one since I was looking for a system to use on my dino bones.  What water separator and desiccant canister do you recommend.  A newbie to this.

Share this post


Link to post
Share on other sites
-AnThOnY-

I have been looking at these for a while. Glad to see a review of them!

Share this post


Link to post
Share on other sites
Ptychodus04
1 hour ago, Kane said:

What is the max safety PSI on this one, Kris?

The instruction sheet lists 150 PSI as the max pressure. That is far higher than one would ever want to use on a fossil. I was pushing 80 PSI through it on my test and I had to be diligent not to remove bone with the matrix. You wouldn't want to start daydreaming while using it.

 

1 hour ago, TyBoy said:

This looks great thanks for sharing.  Might get one since I was looking for a system to use on my dino bones.  What water separator and desiccant canister do you recommend.  A newbie to this.

I have a Camair CT Plus system. It is on the higher end for air filtration so would be a bit of overkill but I didn't have to buy it...

Share this post


Link to post
Share on other sites
Bob Saunders

Years ago I did micron bead blasting of mold machine dies. To get off burnt or stuck debris. Also a Snap on Tools bead cabinet. Both required a big air compressor to keep up. Yours is much smaller so about what CFM  size compressor would you need for home use? I like the idea of just baking soda which is cheap. Are you using the nozzle  inside a small bead/sand blasting cabinet?  

Share this post


Link to post
Share on other sites
Ptychodus04
8 minutes ago, Bob Saunders said:

Years ago I did micron bead blasting of mold machine dies. To get off burnt or stuck debris. Also a Snap on Tools bead cabinet. Both required a big air compressor to keep up. Yours is much smaller so about what CFM  size compressor would you need for home use? I like the idea of just baking soda which is cheap. Are you using the nozzle  inside a small bead/sand blasting cabinet?  

My compressor will push 4.7 CFM at 90 PSI and it has a 21 gallon capacity. It can keep up with everything I throw at it. I'm blasting in a Harbor Freight cabinet. If I have a piece larger than the cabinet, I take it outside.

Share this post


Link to post
Share on other sites
Sagebrush Steve

It see yours is the Mobile Problast.  Do you know what are the differences between this and the Master Mobile Problast?

Share this post


Link to post
Share on other sites
TyBoy

Thank you.  Can you recommend a good air filtration system?

Share this post


Link to post
Share on other sites
Ptychodus04
54 minutes ago, Sagebrush Steve said:

It see yours is the Mobile Problast.  Do you know what are the differences between this and the Master Mobile Problast?

 

I don’t know the difference other than this was in my price range. :D I’m sure Nathan with @Vaniman could tell us.

 

51 minutes ago, TyBoy said:

Thank you.  Can you recommend a good air filtration system?

I don’t have a particular brand recommendation. If you want to use abrasive, you need a filter that removes most of the oil, water, and particles and some kind of dryer. If you’re using scribes only, you just need the first part. A simple inline filter trap would work for that. They can be had fairly inexpensively at most hardware stores or online. 

 

I can’t recommend the Camair setup that I use enough but if you’re not doing a ton of prepping, it’s hard to justify the expense.

Share this post


Link to post
Share on other sites
TyBoy
11 hours ago, Ptychodus04 said:

 

I don’t know the difference other than this was in my price range. :D I’m sure Nathan with @Vaniman could tell us.

 

I don’t have a particular brand recommendation. If you want to use abrasive, you need a filter that removes most of the oil, water, and particles and some kind of dryer. If you’re using scribes only, you just need the first part. A simple inline filter trap would work for that. They can be had fairly inexpensively at most hardware stores or online. 

 

I can’t recommend the Camair setup that I use enough but if you’re not doing a ton of prepping, it’s hard to justify the expense.

Thank you very informative.   One more question can you simply hook up a shop vac to the Harbor Freight cabinet for dust control?

Share this post


Link to post
Share on other sites
Ptychodus04
1 hour ago, TyBoy said:

Thank you very informative.   One more question can you simply hook up a shop vac to the Harbor Freight cabinet for dust control?

You can but the fine dust will quickly clog your filter and will eventually burn out your vac motor. You need a water trap or a cyclone trap to catch it before it gets to the shop vac.

Share this post


Link to post
Share on other sites
TyBoy
11 minutes ago, Ptychodus04 said:

You can but the fine dust will quickly clog your filter and will eventually burn out your vac motor. You need a water trap or a cyclone trap to catch it before it gets to the shop vac.

Is this a better solution?

https://www.harborfreight.com/2-hp-industrial-5-micron-dust-collector-97869.html

Share this post


Link to post
Share on other sites
RJB
On 2/8/2019 at 6:09 AM, Ptychodus04 said:

I have 2 oil/water separators and a desiccant canister filtering the compressed air. The tip is  .048” (1.2mm) sapphire imbedded. I also ordered a .036” (.91mm) tungsten carbide tip for more detailed work.

Ok, I dont mean to sound like a dunse but I also have a desiccant canister and 2 water traps but what is an oil/water seperator? 

 

RB

Share this post


Link to post
Share on other sites
Bob Saunders

I get the impression that the small pancake type air compressors they sell for air pinners and nail guns will not keep up with the volume of air needed. I have little Craftsman twin tank one.  Or else you will be doing short bursts and waiting for it to rebuild the pressure. I did sign up for their online coupon. Not sure I will have enough  need for it. 

Share this post


Link to post
Share on other sites
Ptychodus04
4 hours ago, TyBoy said:

You would want to replace the bag with a 1 micron bag as the really dangerous small particles would go right through the 5 micron bag.

2 hours ago, RJB said:

Ok, I dont mean to sound like a dunse but I also have a desiccant canister and 2 water traps but what is an oil/water seperator? 

 

RB

Same thing but I couldn’t come up with the right terminology when I was typing. The water trap also collects aerosolized oils in the compressed air.

 

1 hour ago, Bob Saunders said:

I get the impression that the small pancake type air compressors they sell for air pinners and nail guns will not keep up with the volume of air needed. I have little Craftsman twin tank one.  Or else you will be doing short bursts and waiting for it to rebuild the pressure. I did sign up for their online coupon. Not sure I will have enough  need for it. 

They won’t keep up. I started out with one and would have to stop working to let it catch up. The one I’m using now is from Harbor Freight and was under $200. I’ve been using it for 3 years without issues (knocks on dining room table).

Share this post


Link to post
Share on other sites
RJB
18 hours ago, Bob Saunders said:

Or else you will be doing short bursts and waiting for it to rebuild the pressure.

Lucky me.  No short burst or waiting with this bad boy!!!

 

RB

DSCN0207.JPG

Share this post


Link to post
Share on other sites
Ptychodus04
2 hours ago, RJB said:

Lucky me.  No short burst or waiting with this bad boy!!!

 

RB

DSCN0207.JPG

:envy:

 

I’ve never coveted another man’s compressor until today. 

Share this post


Link to post
Share on other sites
RJB
23 hours ago, Ptychodus04 said:

 

I’ve never coveted another man’s compressor until today.

Believe me, I didnt start with one this size when I got my first compressor. 

 

RB

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Recently Browsing   0 members

    No registered users viewing this page.

×